Memory BAT mapping: BAT2=256Mb, BAT3=128Mb, residual: 0Mb Total memory = 384MB; using 1024kB for hash table (at c0300000) Linux version 2.4.20-pre7-ben0 (root@merlin) (gcc version 2.95.4 20011002 (Debian prerelease)) #5 Sun Sep 22 14:44:17 EDT 2002 Found Uninorth memory controller & host bridge, revision: 192 Mapped at 0xfdf3c000 Found a Pangea mac-io controller, rev: 0, mapped at 0xfdebc000 Processor NAP mode on idle enabled. PowerMac motherboard: iBook 2 rev. 2 PMU driver 2 initialized for Core99, firmware: 0c CPU HID1 : 0x70000044 Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0 hose pci, pci_mem_offset: 00000000, start0: f1000000 io_base_virt: fd6b5000, io_base_phys: f0000000, isa_mem_base: 00000000 Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0 hose pci, pci_mem_offset: 00000000, start0: f3000000 io_base_virt: fceb3000, io_base_phys: f2000000, isa_mem_base: 00000000 Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0 hose pci, pci_mem_offset: 00000000, start0: f5000000 io_base_virt: fc6b1000, io_base_phys: f4000000, isa_mem_base: 00000000 On node 0 totalpages: 98304 zone(0): 98304 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/hda11 ro hdb=ide-scsi idebus=66 ide_setup: hdb=ide-scsi ide_setup: idebus=66 PowerMac using OpenPIC irq controller OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc66d000 OpenPIC timer frequency is 4.160000 MHz GMT Delta read from XPRAM: -420 minutes, DST: on time_init: decrementer frequency = 24.835213 MHz Console: colour dummy device 80x25 Calibrating delay loop... 1389.36 BogoMIPS Memory: 384500k available (1488k kernel code, 832k data, 292k init, 0k highmem) AGP special page: 0xd7fff000 Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Scanning bus 00 Found 00:58 [106b/0027] 000600 00 Found 00:80 [1002/4c59] 000300 00 Fixup res 1 (101) of dev 00:10.0: 400 -> 802400 Fixups for bus 00 Bus scan for 00 returning with max=00 Scanning bus 10 Found 10:58 [106b/0028] 000600 00 Found 10:b8 [106b/0025] 00ff00 00 Found 10:c0 [106b/0026] 000c03 00 Found 10:c8 [106b/0026] 000c03 00 Fixups for bus 10 Bus scan for 10 returning with max=10 Scanning bus 20 Found 20:58 [106b/0029] 000600 00 Found 20:70 [106b/0030] 000c00 00 Found 20:78 [106b/0024] 000200 00 Fixups for bus 20 Bus scan for 20 returning with max=20 PCI->OF bus map: 0 -> 0 16 -> 0 32 -> 0 PCI:00:10.0: Resource 0: 98000000-9fffffff (f=1208), vd: 1002, dev: 4c59 PCI:00:10.0: Resource 2: 90000000-9000ffff (f=200), vd: 1002, dev: 4c59 PCI:10:17.0: Resource 0: 80000000-8007ffff (f=200), vd: 106b, dev: 0025 PCI:20:0f.0: Resource 0: f5200000-f53fffff (f=200), vd: 106b, dev: 0024 PCI:00:10.0: Resource 1: 00802400-008024ff (f=101), vd: 1002, dev: 4c59 PCI:10:18.0: Resource 0: 80081000-80081fff (f=200), vd: 106b, dev: 0026 PCI:10:19.0: Resource 0: 80080000-80080fff (f=200), vd: 106b, dev: 0026 PCI:20:0e.0: Resource 0: f5000000-f5000fff (f=200), vd: 106b, dev: 0030 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Thermal assist unit using timers, shrink_timer: 200 jiffies CPU clock: 700.000 MHz (400.000-700.000 MHz) Starting kswapd Journalled Block Device driver loaded PCI: Enabling device 00:10.0 (0086 -> 0087) radeonfb: ref_clk=2700, ref_div=12, xclk=16615 from OF radeonfb: detected DFP panel size from EDID: 1024x768 Console: switching to colour frame buffer device 128x48 Registered "ati" backlight controller, level: 15/15 radeonfb: pm reg @50, clk_pwrmgt: 13400, pll_pwrmgt: 1000007, mdll_cko: 43c radeonfb: ATI Radeon M6 LY DDR SGRAM 16 MB radeonfb: DVI port LCD monitor connected radeonfb: CRT port no monitor connected no framebuffer address found for /pci@f0000000/ATY,FallParent@10/ATY,Fall_B input0: Macintosh mouse button emulation pty: 256 Unix98 ptys configured Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 66MHz system bus speed for PIO modes pmac_ide: enabling IDE bus ID 2 Probing IDE interface ide0... Waiting busy 0... wait_busy: last stat: 50, timeout: 59999 -> 1, selecting... Waiting busy 1... wait_busy: last stat: 50, timeout: 9999 -> 1, selecting... Waiting busy 2... wait_busy: last stat: 00, timeout: 9999 -> 1, ready for probe. hda: IBM-IC25N020ATCS04-0, ATA DISK drive hdb: SONY CD-RW CRX800E, ATAPI CD/DVD-ROM drive ide0 at 0xdd214000-0xdd214007,0xdd214160 on irq 19 hda: Enabling Ultra DMA 2 ide_pmac: Set UDMA timing for mode 2, reg: 0x1090038c blk: queue c0276f90, I/O limit 4095Mb (mask 0xffffffff) hda: 39070080 sectors (20004 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(33) Partition check: hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 hda15 hda16 hda17 hda18 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) sungem.c:v0.97 3/20/02 David S. Miller (davem@redhat.com) eth%d: MII PHY ID: 4061e0 BCM 5221 eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:93:b7:d8:88 Macintosh non-volatile memory driver v1.0 apm_emu: APM Emulation 0.5 initialized. usb.c: registered new driver usbdevfs usb.c: registered new driver hub PCI: Enabling device 10:18.0 (0000 -> 0002) PCI: Enabling bus mastering for device 10:18.0 usb-ohci.c: USB OHCI at membase 0xda2cc000, IRQ 27 usb-ohci.c: usb-10:18.0, Apple Computer Inc. KeyLargo/Pangea USB adb: starting probe task... usb.c: new USB bus registered, assigned bus number 1 usb.c: kmalloc IF c08cd1a4, numif 1 usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1 usb.c: USB device number 1 default language ID 0x0 Product: USB OHCI Root Hub SerialNumber: da2cc000 hub.c: USB hub found hub.c: 2 ports detected hub.c: standalone hub hub.c: ganged power switching hub.c: global over-current protection hub.c: Port indicators are not supported hub.c: power on to power good time: 20ms hub.c: hub controller current requirement: 0mA hub.c: port removable status: RR hub.c: local power source is good hub.c: no over-current condition exists hub.c: enabling power on all ports usb.c: hub driver claimed interface c08cd1a4 PCI: Enabling device 10:19.0 (0000 -> 0002) PCI: Enabling bus mastering for device 10:19.0 usb-ohci.c: USB OHCI at membase 0xda2ce000, IRQ 28 usb-ohci.c: usb-10:19.0, Apple Computer Inc. KeyLargo/Pangea USB (#2) usb.c: new USB bus registered, assigned bus number 2 usb.c: kmalloc IF c08cd35c, numif 1 usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1 usb.c: USB device number 1 default language ID 0x0 Product: USB OHCI Root Hub SerialNumber: da2ce000 hub.c: USB hub found hub.c: 2 ports detected hub.c: standalone hub hub.c: ganged power switching hub.c: global over-current protection hub.c: Port indicators are not supported hub.c: power on to power good time: 20ms hub.c: hub controller current requirement: 0mA hub.c: port removable status: RR hub.c: local power source is good hub.c: no over-current condition exists hub.c: enabling power on all ports usb.c: hub driver claimed interface c08cd35c mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 292k init 8k chrp 8k prep adb devices: [2]: 2 c3 [3]: 3 1 [7]: 7 1f ADB keyboard at 2, handler 1 Detected ADB keyboard, type ANSI. input1: ADB HID on ID 2:2.c3 input2: ADB HID on ID 7:7.1f ADB mouse at 3, handler set to 4 (trackpad) input3: ADB HID on ID 3:3.01 adb: finished probe task... Adding Swap: 262136k swap-space (priority -1) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,14), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,15), internal journal EXT3-fs: mounted filesystem with ordered data mode. eth0: MII PHY ID: 4061e0 BCM 5221 eth0: Link is up at 10 Mbps, half-duplex. eth0: Pause is disabled i2c-core.o: i2c core module i2c-core.o: adapter uni-n 0 registered as adapter 0. i2c-core.o: adapter uni-n 1 registered as adapter 1. Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits i2c-core.o: adapter mac-io 0 registered as adapter 2. Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits tas driver [TAS3004 driver V 0.3]) using i2c address: 0x35 from device-tree i2c-core.o: driver TAS3004 driver V 0.3 registered. i2c-core.o: client [tas Digital Equalizer] registered to adapter [mac-io 0](pos. 0). Audio jack unplugged, enabling speakers. AE-Init snapper mixer PowerMac Snapper DMA sound driver rev 016 installed Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07 Write will use 4 fragments of 32768 bytes as default ide_pmac: Set PIO timing for mode 4, reg: 0x1090014a eth0: Link is up at 10 Mbps, half-duplex. eth0: Pause is disabled eth0: Link is up at 10 Mbps, half-duplex. eth0: Pause is disabled eth0: Link down ide_pmac: Set PIO timing for mode 4, reg: 0x1090014a usb-ohci.c: USB suspend: usb-10:18.0 usb-ohci.c: USB suspend: usb-10:19.0 eth0: suspending, WakeOnLan disabled hdb: channel busy CLK_PIN_CNTL on wakeup was: 00000005 hda: Enabling Ultra DMA 2 ide_pmac: Set UDMA timing for mode 2, reg: 0x1090038c PCI: Enabling bus mastering for device 10:18.0 usb-ohci.c: USB continue: usb-10:18.0 from host wakeup PCI: Enabling bus mastering for device 10:19.0 usb-ohci.c: USB continue: usb-10:19.0 from host wakeup eth0: resuming adb: starting probe task... adb devices: [2]: 2 c3 [3]: 3 1 [7]: 7 1f ADB keyboard at 2, handler 1 ADB mouse at 3, handler set to 4 (trackpad) adb: finished probe task... Audio jack unplugged, enabling speakers. ide_pmac: Set PIO timing for mode 4, reg: 0x1090014a hermes.c: 5 Apr 2002 David Gibson orinoco.c 0.11b (David Gibson and others) airport.c 0.11b (Benjamin Herrenschmidt ) eth1: Station identity 001f:0001:0008:000c eth1: Looks like a Lucent/Agere firmware version 8.12 eth1: Ad-hoc demo mode supported eth1: IEEE standard IBSS ad-hoc mode supported eth1: WEP supported, 104-bit key eth1: MAC address 00:30:65:06:34:FE eth1: Station name "HERMES I" eth1: ready airport: card registered for interface eth1 ide_pmac: Set PIO timing for mode 4, reg: 0x1090014a ide_pmac: Set PIO timing for mode 4, reg: 0x1090014a